Servo Programmer Program Card for EMAX digital Servos

SKU:EMAX-S-P-1

$15.00

Availability: In stock, Processing Time 3-4 Work Days.

RCD3007 Universal Remote Controlled Nitro Engine Glow Plug Driver CDI Ignition 4.5~16V for RC Airplane Helicopter

Product Description

Features:
1.Expand the Zipped format file and disable the antivirus softwares before you install
the softwares before you install the software to the computer.
2.Open the file as unzipped before,Double-click the file (named
USBXpressInstaller.exe under the folder
named Driver) to begin installation.
3.Restart the computor,please do not remove the file evenif any warning pops up.
4.Run the software , and you will see the interface as below:


Connect the USB adapter to PC and the Servo Programmer , the servo MUST be
connected to USB adapter correctly.
( Please pay attention to the wires .) Click the "REFLASH USB" button and the PC
indicates that the servois found,
and the Green LED is ON.Before you change any programming values, please
choose the button "Read config"
and you will see the default settings of the servo,click"Save"button to save the default
settings of the servo .
This is useful if there is any problem after any programming values are changed,you
can resume the default settings
by clicking the"load"button then"Write config"button.(This Green LED is on indicating
that the programming clicking goes
on smoothly .If the Red LED is on,please turn off the software and check if the wires
are connected correctly .
If it the Red LED is still on , please re-install the software)
After the software is read you can set the values according to the following instruction
. Clink the "Write config"
button to write the program to the servo.
Programmable servos:EMAX ES09D, ES09MD, ES3351, ES3352, ES9256HV,
ES9257, ES9258, ES9054, ES9254, ES9255
(more new servos will be added to this list)
Programming
Dead Band is the range of signal over servo does not change in response to a
change in signal.
The smaller the value is, the more sensitive the servo is. It will cause vibration or
shorten the life for servos of this
value is set too low.
Stretcher:Please do not change this value.
Adjust motor drive torque, Max. 245. Please kindly note that the higher the torque is
,the bigger the current is ,
and bigger current will shorten servo life and cause vibration. Adjusting 100% PWM
value together with this value allows you ti adjust servo output torque as well.
Boost:The Pulse-Width to start the motor . It makes the servo more smooth by
adjusting the values . It will cause the vibration if the too small.
Pulse Lower Recommended value :900us , Min. 600us. Servo travel range angle
pulse Lower : can be adjusted by changing this value.
Pulse Hight Recommended value : 2100us. Max .2400us .
Left Range : To set the Max . value . The value is usually set to be 0 . The servo
travel degree will decrease will decrease with the value of - ,and increase with the
value of + .
This feature allows you to change the servo degree in corresponding to the same
pulse width.
Right Range :To set the Max . value is usually set to be 0 . The servo travel degree
will decrease with the value of -, and increase with the value of + 。
This feature allows you to change the servo degree in corresponding to the same
pulse width.
Neutral : this feature allows you to set you to set your Center point . The value is
usually set be 0 . Please do not change this value.
Drive Frequency : It allows you to lower the squeaky noise of the sevso .
Recommended value: 330,19531. Other value may cause servo .
Internal Osc : When this feature is chosen external oscillator is unnecessary . Please
don't change this mode or else it will cause servo malfunction.
Inverter :To change the direction of rotation of the servo for a given stick movement
direction : 100% PWM:Adjust servo torque.
when Narrow Band is chosen , IC is set to be Narrow Band mode , the range of
signal recognition will be changed . Please do not choose this feature if the gyro
doesn't supprt Narrow Band mode.


Package include:
EMAX Servo Programmer x1
USB Data Cable x1

    Servo Programmer Program Card for EMAX digital Servos

    Servo Programmer Program Card for EMAX digital Servos

    Servo Programmer Program Card for EMAX digital Servos

    Servo Programmer Program Card for EMAX digital Servos

    Servo Programmer Program Card for EMAX digital Servos

Additional Information

Name Servo Programmer Program Card for EMAX digital Servos
SKU EMAX-S-P-1
Weight(KG) 0.1500
Free Shipping No
Brand Emax
Color No

Shipping & Payment

Payment Methods:

  • PayPal
  • Western Union
  • Wire Transfer Bank

 More detail 

How Long Will It Take To Deliver?

The total delivery time is separated into two parts, the processing time and the shipping time.
The processing time is the time from when your payment is received to when we gather all the items and package them,
which takes approximately 3 to 5 working days.
The shipping time is the time it takes for the package to be delivered by the couriers to the final destination.

  • Standard shipping time takes approximately 6 to 15 working days
  • Expedited shipping time takes approximately 4 to 10 working days.
  • If free shipping products, it will cost about 6 to 15 days.

All Ship Method choose:EMS,DHL,FEDEX,UPS,TNT,ARAMEX,TOLL,DPEX.

We are not by ePacket,Post Air Parcel.

Product Tags

Add your tags

Use spaces to separate tags. Use single quotes (') for phrases.